Description
W-125 (WP-125)
Genuine Weldcraft® Miller® Micro TIG Torch Package. 125 Amp Water-Cooled. Available with 25' (7.6m) Flexible Rubber Power, Water and Gas Hoses. Torch package includes 1/16" (1.6mm) 45 Degree Electrode Chuck and Gas Nozzle.
Torch Body Lengths:
- 3.5" (88.9mm)
- 5" (127mm)
Note: 160 Amp (DCSP) Rating When Using 3/32" (2.4mm) Electrode and Quartz Nozzles.
| Specifications: | W-125 (MT-125) | |||||||
|---|---|---|---|---|---|---|---|---|
| Amperage | 125A DCSP or 80A ACHF @ 100% Duty Cycle. 160 Amp (DCSP) Rating when using 3/32" (2.4mm) Electrode & Quartz Cup |
|||||||
| Water-Cooled body | 90°, 45°, & 180° Nozzles (Sold Separately) | |||||||
| Electrode capacity | .040" (1mm) -- 3/32" (2.4mm) | |||||||
| Head size | Varies by chuck/nozzle type from 5/8" (15.8mm) to 3/4" (19.0mm) long | |||||||
| Torch body weight | 2.4 oz. (68.0g) | |||||||
| Torch neck length | WP-125M, 3.5" (88.9mm) WP-125L, 5" (127mm) |
|||||||
| Handle diameter | 3/4" (19.1mm) | |||||||
| Power Connection | 7/8"-14LH Male | |||||||
| Gas Connection | 5/8"-18RH Male | |||||||
| Water Connection | 5/8"-18LH Male | |||||||
| Part # | WP-125M | WP-125M-HDL | WP-125L | WP-125L-HDL | WP-125M-12-R | WP-125M-25-R | WP-125L-12-R | WP-125L-25-R |
| Handle | N/A | 53N06 | N/A | 53N06 | 53N06 | 53N06 | 53N06 | 53N06 |
| Cable Material | N/A | N/A | N/A | N/A | Super Flex | Super Flex | Super Flex | Super Flex |
| Cable Length | N/A | N/A | N/A | N/A | 12.5' (3.8m) | 25' (7.6m) | 12.5' (3.8m) | 25' (7.6m) |
Set-Up Tips:
Note: This torch is a delicate instrument and should be setup carefully to ensure parts life and high-quality welds. For best results Arc-Zone recommends our cut-to-length and pre-ground tungsten electrodes.
Tungsten Electrode Positioning/Tightening Instructions:
- Tighten 45° & 90° electrode chucks using the inserted tungsten as a lever by rotating clockwise. The tungsten should be inserted through the nozzle orifice, and through the electrode hole in the chuck so that it is flush and does not restrict gas flow.
Note: Take care to rotate nozzle simultaneously so as not to force tungsten against nozzle causing it to break! - Adjust Tungsten length so that rear of tungsten is flush with rear of chuck and protrudes approx. 1/8" beyond the nozzle.
Note: The electrode must not protrude past the backside of the electrode holding chuck, or it will cause reduced gas flow resulting in poor quality gas coverage.
- When using the P/N (125N90S) low profile 90° nozzle, the tungsten should be inserted through the nozzle orifice, and through the electrode hole in the chuck so that it is flush and does not rest rick gas flow
- Tighten 180° straight style chucks with Chuck Wrench P/N (53N20). The tungsten should be inserted through the nozzle orifice, through the electrode hole in the chuck so that it is flush and does not restrict gas flow.
Additional Information
TIG Torch Type: |
Water Cooled |
TIG Process: |
Hand Held |
Torch Model: |
Specialty Torches |
Amperage Rating: |
100 - 130 Amp |
